|
|
|
|
 AIr Filter Assembly - Complete air filter assembly includes cover, filter element and mount assembly |
$28 |
|
Axle - Rear Axle -  |
|
na |
|
Bearings - replacement bearing pair (1 pair required per wheel) |
$12 |
|
|
Brake Cable - Brake Cable for models using a single brake cable to a single rear caliper |
$19 |
|
| Brake Cable - Brake Cable for models using 3 cables, one long and two short - only short cable are available ( the long cable that goes to a splitter/ carrier is not available) |
$12 |
|
Brake Caliper - w/ Pads type CW  usually installed on the left side on top of or behind the axle |
$24 |
|
| Brake Caliper - w/ Pads Type CCW Usually installed on the right side on tob of or behind the axle |
$24 |
|
| Brake Handle - Left Hand Brake Handle- clamp on style for round handle bars |
$21 |
|
| Brake Handle - Left Hand Brake Handle- bolt thru style - has a short lever (about 2 inches) |
$32 |
|
| Brake Pads - Disk Brake Pad Pair
- Rectangle Shaped w/ rounded corners and center groove ~1"x.75" overall |
$12 |
|
| Brake Pads - Disk Brake Pad Pair
- U Shaped w/ rounded corners and center groove ~1"x1" overall |
$12 |
|
|
Carburetor - for 5.5hp engine |
$38 |
|
| Carburetor - Performance Carburetor |
$65 |
|
| Carburetor Repair Kit - |
na |
na |
| Carburetor Parts - |
na |
na |
| Chain - Chain 3ft length, enough for one chain, includes 2 master links |
$26 |
|
|
Chain - Chain 5ft length, enough for about two chains, includes 3 master links |
$34 |
|
|
Chain Master - Two
Master Links |
$9 |
|
|
Clutch - replacement clutch for TY Rod 4 gokart with sprocket |
$44 |
|
|
Cylinder - |
na |
na |
|
Engine 5.5hp - Complete running
Engine w/ Intake and Exhaust - Bolt It On And Go! Does not include clutch. |
$195 |
|
| Engine 5.5hp - California Version, cARB approved. Complete running
Engine w/ Intake and Exhaust - Bolt It On And Go! Does not include clutch. |
$245 |
|
| Gas Tank w/cap Gas tank with cap and fuel line fitting |
$38 |
|
|
Ignition Coil - Spark
Plug Coil & Wire Assembly - image and distance between mounting holes required |
$22 |
|
| kill switch - kill switch, single wire type, mounts into hole on steering wheel. Includes switch, nut and 6" lead wire) |
$6 |
|
| Muffler - stock muffler with cover and gasket |
$25 |
|
| Pull Start - Complete Recoil Pull Start Assembly for your TyRod
IV Kart w/ Pull Rope Installed - ( plastic pulley center on backside of pull start ) |
$58 |
|
|
Pull Start - Complete Recoil Pull Start Assembly for your TyRod
IV Kart w/ Pull Rope Installed - ( Metal pulley center on backside of pull start ) |
$58 |
|
| SEAT - aftermarket seat hard plastic, unupolstered, may require minor modifications to mount. |
$48 |
|
|
Spark Plug - NGK / Champion |
$5 |
|
|
Spindle - Front Wheel
Axle - Left & Right Pair - Connects the Wheel To
The Frame And Tie Rod - |
na |
na |
|
Sprocket - Engine / Transmission
Sprocket - see clutch above |
$na |
|
| Sprocket - For Axle/Wheel - specifications required - (chain pitch, bolt hole pattern w/ distance overall diameter) and image required |
na |
|
Steering wheel - replacement steering wheel - accepts clamp on style controls |
$30 |
|
Steering wheel - with Brake + Throttle Levers replacement steering wheel and levers |
$55 |
|
Throttle Cable - Replacement throttle cable |
$23 |
|
| Throttle - Aftermarket Throttle, Clamp on type for use with round bar steering wheels - NOTE: must have bare metal rod to clamp to. if you have a round bar with padding the padding will need to be cut away |
$22 |
|
| Throttle - Aftermarket Throttle, bolt through handle bar type, Used with both bare and padded ( flat metal and tube type) handle bars - Note: must have a bolt hole through the bar to mount |
$39 |
|
|
Tie Rod - Pair (left
& right tie rod) |
na |
na |
|
Tire - front - Replacement knobby tire |
$ 24 |
|
| Tire -rear - Replacement knobby tire |
$ 24 |
|
| Tire Tube - Replacement inner tube |
$ 9 |
|
| Wheel - unavailable - please try azusaeng.com for the nearest fit we could find |
na |
na |
 |
|
|
